Please select and order
€64.38
excl. VAT
CONFIGURE NOW
Norm
ÖNORM EN ISO 10350-1
Issue date: 2014 11 01
Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2007 + Amd 1:2014) (consolidated version)
ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property ...
Read more
Withdrawn
: 2018 03 15
Publisher:
Austrian Standards International
Format:
Digital | 16 Pages
Language:
German
| English
| Download GER/ENG
Currently valid:
Optionally co-design standards:
ICS
ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions. The properties included are those presented conventionally in manufacturers' data sheets. This part of ISO 10350 applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials that may be injection- or compression-moulded or prepared as sheets of specified thickness. Part 2 of ISO 10350 deals specifically with long- or continuous-fibre-reinforced plastics. For the purposes of ISO 10350, long-fibre-reinforced plastics are considered to have fibre lengths greater than 7,5 mm prior to moulding.
ÖNORM EN ISO 10350-1
2018 03 15
Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials...
Norm
ÖNORM EN ISO 10350-1
2014 11 01
Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials...
Norm
↖
ÖNORM EN ISO 10350-1
2010 03 01
Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials...
Norm
ÖNORM EN ISO 10350-1
2009 11 01
Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials...
Norm
ÖNORM EN ISO 10350-1
2001 02 01
Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials...
Norm
Norm
ISO 75-1:2013
Issue date :
2013 04 09
Plastics — Determination of temperature of deflection under load — Part 1: General test method
Norm
ISO 75-2:2013
Issue date :
2013 04 09
Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
Norm
ISO 179-1:2010
Issue date :
2010 06 04
Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
Norm
ISO 179-2:1997
Issue date :
1997 12 18
Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
Norm
ISO 291:2008
Issue date :
2008 04 22
Plastics — Standard atmospheres for conditioning and testing
Norm
ISO 293:2004
Issue date :
2004 05 11
Plastics — Compression moulding of test specimens of thermoplastic materials
Norm
ISO 294-1:1996
Issue date :
1996 12 26
Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
Norm
ISO 294-3:2002
Issue date :
2002 06 13
Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates
Norm
ISO 294-4:2001
Issue date :
2001 12 20
Plastics — Injection moulding of test specimens of thermoplastic materials — Part 4: Determination of moulding shrinkage
Norm
ISO 295:2004
Issue date :
2004 01 14
Plastics — Compression moulding of test specimens of thermosetting materials
Norm
ISO 306:2013
Issue date :
2013 11 08
Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
Norm
ISO 527-1:2012
Issue date :
2012 02 22
Plastics — Determination of tensile properties — Part 1: General principles
Norm
ISO 527-2:2012
Issue date :
2012 02 22
Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
Norm
ISO 899-1:2003
Issue date :
2003 06 03
Plastics — Determination of creep behaviour — Part 1: Tensile creep
Norm
ISO 1183-1:2012
Issue date :
2012 05 11
Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pyknometer method and titration method
Norm
ISO 1183-2:2004
Issue date :
2004 07 14
Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method
Norm
ISO 1183-3:1999
Issue date :
1999 09 30
Plastics — Methods for determining the density of non-cellular plastics — Part 3: Gas pyknometer method
Norm
ISO 2577:2007
Issue date :
2007 12 03
Plastics — Thermosetting moulding materials — Determination of shrinkage
Norm
ISO 4589-2:1996
Issue date :
1996 07 18
Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
Norm
ISO 6603-2:2000
Issue date :
2000 09 21
Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing
Norm
ISO 10724-1:1998
Issue date :
1998 11 19
Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens
Norm
ISO 10724-2:1998
Issue date :
1998 11 19
Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates
Norm
ISO 11357-2:2013
Issue date :
2013 04 15
Plastics — Differential scanning calorimetry (DSC) — Part 2: Determination of glass transition temperature and glass transition step height
Norm
ISO 11357-3:2011
Issue date :
2011 04 28
Plastics — Differential scanning calorimetry (DSC) — Part 3: Determination of temperature and enthalpy of melting and crystallization
Norm
ISO 11359-2:1999
Issue date :
1999 10 07
Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
Norm
IEC 60695-11-10
Issue date :
1999 03 31
Fire hazard testing Test flames -- 50 W horizontal and vertical flame test methods
Norm
IEC 60695-11-20
Issue date :
1999 03 31
Fire hazard testing Test flames -- 500 W flame test methods
Norm
ISO 75-1:2020
Issue date :
2020 02 28
Plastics — Determination of temperature of deflection under load — Part 1: General test method
Norm
ISO 75-2:2013
Issue date :
2013 04 09
Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
Norm
ISO 179-1:2010
Issue date :
2010 06 04
Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
Norm
ISO 179-2:2020
Issue date :
2020 05 14
Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
Norm
ISO 291:2008
Issue date :
2008 04 22
Plastics — Standard atmospheres for conditioning and testing
Norm
ISO 293:2004
Issue date :
2004 05 11
Plastics — Compression moulding of test specimens of thermoplastic materials
Norm
ISO 294-1:2017
Issue date :
2017 05 10
Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
Norm
ISO 295:2004
Issue date :
2004 01 14
Plastics — Compression moulding of test specimens of thermosetting materials
Norm
ISO 306:2013
Issue date :
2013 11 08
Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
Norm
ISO 527-1:2019
Issue date :
2019 07 26
Plastics — Determination of tensile properties — Part 1: General principles
Norm
ISO 527-2:2012
Issue date :
2012 02 22
Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
Norm
ISO 1183-1:2019
Issue date :
2019 02 28
Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pycnometer method and titration method (Corrected version 2019-05)
Norm
ISO 1183-2:2019
Issue date :
2019 02 28
Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method
Norm
ISO 1183-3:1999
Issue date :
1999 09 30
Plastics — Methods for determining the density of non-cellular plastics — Part 3: Gas pyknometer method
Norm
ISO 2577:2007
Issue date :
2007 12 03
Plastics — Thermosetting moulding materials — Determination of shrinkage
Norm
ISO 4589-2:2017
Issue date :
2017 04 12
Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
Norm
ISO 10724-1:1998
Issue date :
1998 11 19
Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens
Norm
ISO 10724-2:1998
Issue date :
1998 11 19
Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates
Norm
ISO 11357-2:2020
Issue date :
2020 03 02
Plastics — Differential scanning calorimetry (DSC) — Part 2: Determination of glass transition temperature and step height
Norm
ISO 11357-3:2018
Issue date :
2018 03 16
Plastics — Differential scanning calorimetry (DSC) — Part 3: Determination of temperature and enthalpy of melting and crystallization
Norm
ISO 11359-2:1999
Issue date :
1999 10 07
Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
Norm
IEC 60695-11-10
Issue date :
1999 03 31
Fire hazard testing Test flames -- 50 W horizontal and vertical flame test methods
Norm
IEC 60695-11-20
Issue date :
1999 03 31
Fire hazard testing Test flames -- 500 W flame test methods
Norm
ÖNORM EN ISO 10350-1
Issue date :
2018 03 15
Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2017)