Please select and order
€98.22
excl. VAT
Add to cart
Norm
ÖNORM EN ISO 10684
Issue date: 2004 11 01
Fasteners - Hot dip galvanized coatings (ISO 10684:2004)
This International Standard specifies material, process, dimensional and some performance requirements for
hot dip spun galvanized coatings applied to coarse threaded st...
Withdrawn: 2009 05 15
Publisher:
Austrian Standards International
Format:
Digital | 24 Pages
Language:
German
| English
Currently valid:
Optionally co-design standards:
This International Standard specifies material, process, dimensional and some performance requirements for
hot dip spun galvanized coatings applied to coarse threaded steel fasteners from M8 up to and including M64
and for property classes up to and including 10.9 for bolts, screws and studs and 12 for nuts. It is not
recommended to hot dip galvanize threaded fasteners in diameters smaller than M8 and/or with pitches below
1,25 mm.
NOTE Attention is drawn to the fact that the proof loads and stresses under proof load of oversize tapped nuts with
threads M8 and M10 and the ultimate tensile loads and proof loads of undersize threaded bolts and screws with threads
M8 and M10 are reduced as compared to the values specified in ISO 898-2 and ISO 898-1 respectively and are specified
in Annex A.
It primarily concerns the spun hot dip galvanizing of threaded steel fasteners, but it may also be applied to
other threaded steel parts.
The specifications given in this International Standard may also be applied to non-threaded steel parts such
as washers.
ÖNORM EN ISO 10684
2009 05 15
Fasteners - Hot dip galvanized coatings (ISO 10684:2004 + Cor 1:2008) (consolidated version)
Norm
ÖNORM M 5001-10
1979 06 01
Fasteners and similar parts; technical specifications, hot dip zinc galvanized parts
Norm
ÖNORM M 5001
1958 02 03
Schrauben, Muttern, Scheiben und ähnliche Gewinde-und Formteile; technische Lieferbedingungen
Norm
ÖNORM M 5001
1923 01 31
Blanke Sechskantschrauben für 1 und 2 Muttern oder 1 Kronenmutter von 1,7 - 10 mm; metrisches Gewind...
Norm
Norm
Issue date :
1992 10 08
Metallic coatings — Hot dip galvanized coatings on ferrous materials — Gravimetric determination of the mass per unit area
Norm
Issue date :
1999 02 04
Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods
Final Draft
Issue date :
2009 01 29
Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods
Norm
Issue date :
1996 10 03
Metallic and other inorganic coatings — Definitions and conventions concerning the measurement of thickness
Norm
Issue date :
1982 08 01
Non-magnetic coatings on magnetic substrates — Measurement of coating thickness — Magnetic method
Norm
Issue date :
1999 08 26
Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs
Final Draft
Issue date :
2008 11 27
Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread
Norm
Issue date :
1992 11 12
Mechanical properties of fasteners — Part 2: Nuts with specified proof load values — Coarse thread
Norm
Issue date :
1998 12 20
ISO general-purpose metric screw threads — Tolerances — Part 1: Principles and basic data
Norm
Issue date :
1998 12 20
ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw threads — Medium quality
Norm
Issue date :
1998 12 20
ISO general purpose metric screw threads — Tolerances — Part 3: Deviations for constructional screw threads
Norm
Issue date :
1998 12 20
ISO general purpose metric screw threads — Tolerances — Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing
Norm
Issue date :
1998 12 20
ISO general purpose metric screw threads — Tolerances — Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing
Norm
Issue date :
1994 05 01
Mechanical properties of fasteners - Part 2 : Nuts with specified proof load values - Coarse thread (ISO 898-2:1992)
Norm
Issue date :
1995 02 01
Metallic coatings - Hot dip galvanized coatings on ferrous materials - Gravimetric determination of the mass per unit area (ISO 1460:1992)
Norm
Issue date :
1999 04 01
Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:1999)
Norm
Issue date :
2008 01 01
Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO/DIS 1461:2007)
Norm
Issue date :
2000 06 01
Metallic and other inorganic coatings - Definitions and conventions concerning the measurement of thickness (ISO 2064:1996)
Norm
Issue date :
1995 04 01
Non-magnetic coatings on magnetic substrates - Measurement of coating thickness - Magnetic method (ISO 2178:1982)
Norm
Issue date :
1999 12 01
Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs (ISO 898-1:1999)
Norm
Issue date :
2007 02 01
Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs (ISO/DIS 898-1:2006)
Norm
Issue date :
2012 03 16
Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread
Norm
Issue date :
2013 09 13
ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data
Norm
Issue date :
1998 12 20
ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw threads — Medium quality
Norm
Issue date :
2021 07 06
ISO general purpose metric screw threads — Tolerances — Part 3: Limit deviations for screw threads
Norm
Issue date :
2021 07 06
ISO general purpose metric screw threads — Tolerances — Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing
Norm
Issue date :
1998 12 20
ISO general purpose metric screw threads — Tolerances — Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing
Norm
Issue date :
2020 09 14
Metallic coatings — Hot dip galvanized coatings on ferrous materials — Gravimetric determination of the mass per unit area
Norm
Issue date :
2009 05 07
Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods
Norm
Issue date :
1996 10 03
Metallic and other inorganic coatings — Definitions and conventions concerning the measurement of thickness
Norm
Issue date :
2016 03 17
Non-magnetic coatings on magnetic substrates — Measurement of coating thickness — Magnetic method
Norm
Issue date :
2009 05 15
Fasteners - Hot dip galvanized coatings (ISO 10684:2004 + Cor 1:2008) (consolidated version)