Jetzt auswählen und bestellen
72,72 €
exkl. USt.
Konfigurieren
Norm
ÖNORM EN 1612-2
Ausgabedatum: 2009 12 01
Plastics and rubber machines - Reaction moulding machines - Part 2: Safety requirements for reaction moulding plant
This standard covers the essential health and safety requirements for the design of reaction moulding plant
with the exception of metering and mixing units (for these se...
Weiterlesen
ZURÜCKGEZOGEN
: 2019 05 01
Herausgeber:
Austrian Standards International
Format:
Digital | 23 Seiten
Sprache:
Englisch
Standards mitgestalten:
ICS
Fachgebiete
Mechanical & plant engineering, Rubber industry. Plastics industry, Equipment for the rubber and plastics industries
Safety, Rubber industry. Plastics industry, Equipment for the rubber and plastics industries
Chemistry, paper & textiles, Rubber industry. Plastics industry, Equipment for the rubber and plastics industries
This standard covers the essential health and safety requirements for the design of reaction moulding plant
with the exception of metering and mixing units (for these see part 1).
The significant and specific hazards are listed in clause 4 and are dealt with in this standard.
This standard does not cover completely the hazards arising from the use of highly flammable additives, for
example pentane used as a blowing agent (see 4.3), because these hazards depend to a large extent on the
additives and process used.
This standard does not cover the hazards due to noise generated by the cutting unit, which is the only
significant source of noise at such plant.
This standard does not cover the requirements for the design of exhaust systems.
This standard does not cover the hazards arising from the assembly of separate units not supplied at the
same time by the same manufacturer.
This standard applies to reaction moulding plant manufactured after the date of publication of this standard.
ÖNORM EN 1612-2
2009 12 01
Plastics and rubber machines - Reaction moulding machines - Part 2: Safety requirements for reaction...
Norm
↖
ÖNORM EN 1612-2
2000 09 01
Gummi- und Kunststoffmaschinen - Reaktionsgießmaschinen - Teil 2: Sicherheitsanforderungen an Reakti...
Norm
Norm
ÖNORM EN ISO 13857
Ausgabedatum :
2008 08 01
Sicherheit von Maschinen - Sicherheitsabstände gegen das Erreichen von Gefährdungsbereichen mit den oberen und unteren Gliedmaßen (ISO 13857:2008)
Norm
ÖNORM EN 349
Ausgabedatum :
2008 09 01
Sicherheit von Maschinen - Mindestabstände zur Vermeidung des Quetschens von Körperteilen
Norm
ÖNORM EN 1037
Ausgabedatum :
2008 11 01
Sicherheit von Maschinen - Vermeidung von unerwartetem Anlauf
Norm
ÖNORM EN 574
Ausgabedatum :
2009 06 15
Sicherheit von Maschinen - Zweihandschaltungen - Funktionelle Aspekte - Gestaltungsleitsätze
Norm
ÖNORM EN 1612-1
Ausgabedatum :
2009 04 15
Kunststoff- und Gummimaschinen - Reaktionsgießmaschinen - Teil 1: Sicherheitsanforderungen an Misch- und Dosiereinheiten
Norm
ÖNORM EN 953
Ausgabedatum :
2009 06 01
Sicherheit von Maschinen - Trennende Schutzeinrichtungen - Allgemeine Anforderungen an Gestaltung und Bau von feststehenden und beweglichen trennenden Schutzeinrichtungen
Norm
ÖNORM EN 1127-1
Ausgabedatum :
2011 09 01
Explosionsfähige Atmosphären - Explosionsschutz - Teil 1: Grundlagen und Methodik