Please select and order
€98.22
excl. VAT
Add to cart
Norm

ÖNORM EN ISO 20753

Issue date: 2019 01 01

Plastics - Test specimens (ISO 20753:2018)

This document specifies dimensional requirements relating to test specimens prepared from plastics materials intended for processing by moulding, as well as to test speci...
Withdrawn: 2024 03 01
Publisher:
Austrian Standards International
Format:
Digital | 23 Pages
Language:
German | English | Download GER/ENG
Optionally co-design standards:
This document specifies dimensional requirements relating to test specimens prepared from plastics materials intended for processing by moulding, as well as to test specimens prepared by machining from sheets or shaped articles. It compiles the designations and dimensions of test specimens used for the acquisition of comparable data and also of other frequently used specimens. The following types of test specimen are specified: a) Type A1 and type A2 specimens (1 = injection moulded, 2 = machined from a sheet or shaped article) These are tensile test specimens from which, with simple machining, specimens for a variety of other tests can be taken. The type A1 specimen is a multipurpose test specimen. The principal advantage of a multipurpose test specimen is that it allows all the test methods mentioned in Annex A to be carried out by all test laboratories on the basis of comparable mouldings. Consequently, the properties measured are coherent as all are measured using similar specimens prepared in the same way. In other words, it can be expected that test results for a given set of specimens will not vary appreciably due to unintentionally different moulding conditions. On the other hand, if desired, the influence of moulding conditions and/or different states of the specimens can be assessed without difficulty for all of the properties measured. Also described are reduced-scale test specimens designated type Axy, where x is the number indicating the method of specimen preparation (1 = injection moulded, 2 = machined from a sheet or shaped article) and y is a number indicating the scale factor (1:y). These can be used e.g. when full-sized test specimens are not convenient or when sample material exists in small quantities only. b) Type B specimens These are bar specimens which can be directly moulded or can be machined from the central section of type A1 specimens or from sheets or shaped articles. c) Type C specimens These are small tensile test specimens which can be directly moulded or machined, e.g. from plates (Type D or type F specimens), from the central section of type A1 specimens or from sheets or shaped articles. d) Type D1 and type D2 specimens These are square plates of thickness 1 mm and 2 mm, respectively. e) Type F specimens These are rectangular plates intended for use in the analysis of mechanical anisotropy. If a particular type of test specimen is not mentioned in this document, this does not mean that there is any intention to exclude the use of the specimen. Additional specimen types can be added in future if they are commonly used.
ÖNORM EN ISO 20753
2024 03 01
Plastics - Test specimens (ISO 20753:2023)
Norm
ÖNORM EN ISO 20753
2019 01 01
Plastics - Test specimens (ISO 20753:2018)
Norm
ÖNORM EN ISO 20753
2014 08 01
Plastics - Test specimens (ISO 20753:2008)
Norm
Norm
ISO 293:2004
Issue date : 2004 05 11
Plastics — Compression moulding of test specimens of thermoplastic materials
Norm
ISO 294-1:2017
Issue date : 2017 05 10
Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
Norm
ISO 294-2:2018
Issue date : 2018 12 07
Plastics — Injection moulding of test specimens of thermoplastic materials — Part 2: Small tensile bars
Norm
ISO 294-3:2020
Issue date : 2020 06 26
Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates
Norm
ISO 294-5:2017
Issue date : 2017 11 09
Plastics — Injection moulding of test specimens of thermoplastic materials — Part 5: Preparation of standard specimens for investigating anisotropy
Norm
ISO 295:2004
Issue date : 2004 01 14
Plastics — Compression moulding of test specimens of thermosetting materials
Norm
ISO 2818:2018
Issue date : 2018 12 13
Plastics — Preparation of test specimens by machining
Norm
ISO 10350-1:2017
Issue date : 2017 10 11
Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials
Norm
ISO 10350-2:2020
Issue date : 2020 07 22
Plastics — Acquisition and presentation of comparable single-point data — Part 2: Long-fibre-reinforced plastics
Norm
ISO 10724-1:1998
Issue date : 1998 11 19
Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens
Norm
ISO 11403-1:2021
Issue date : 2021 06 18
Plastics — Acquisition and presentation of comparable multipoint data — Part 1: Mechanical properties
Norm
ISO 11403-2:2012
Issue date : 2012 09 03
Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and processing properties
Norm
ISO 11403-3:2021
Issue date : 2021 06 18
Plastics — Acquisition and presentation of comparable multipoint data — Part 3: Environmental influences on properties
Norm
ÖNORM EN ISO 20753
Issue date : 2024 03 01
Plastics - Test specimens (ISO 20753:2023)
Norm
ISO 20753:2018
Issue date : 2018 10 19
Plastics — Test specimens